AT-2 R-SPEC is not available regrinding .
(FAQID:9092)
スレッドミル | オーエスジー
43 件中 1-10 件を表示
No : 9092
公開日時 : 2025/03/07 00:00
更新日時 : 2025/04/17 07:24
カテゴリー：
General
threadmill is engraved with INT. What does this mean?
INT stands for INTERNAL, which means for internal thread processing.
(FAQID:161)
No : 161
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection
Is there a chip interchangeable thread mill that can process tapered threads for PT1/8 and PT1/4 pipes?
Indexable type ( chip in
No : 162
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:39
カテゴリー：
Tool selection
I want the movement of the thread mill to be from top to bottom. [ThreadPro]
When using ThreadPro, an NC program creation tool for thread mills, you can do the following.
In the case of right-hand thread...
For right-handed (right-turned) cutters, the up-cut selection allows you to specify the movement of the tool
No : 163
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/04 14:49
カテゴリー：
Program creation
The actual thread mill is engraved with L45. What does this mean?
It is a lead with a groove twist. Lead refers to the straight-line distance of the spiral when one lap.
(FAQID:165)
No : 165
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection
chip Can the inserts of the interchangeable thread mill be used on both sides by interchanging the front and back?
In the case of parallel scr
No : 167
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:39
カテゴリー：
Tool selection
Can the holder for tapered threads (TMNC) for pipes also process parallel threads?
It's possible.
On the other hand, even if the standard type TMC holder is equipped with an insert for tapered threads for pipes, it can be use
No : 168
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection
I processed it with a thread mill, but I would like to adjust the dimensions of the screw a little more.
Is
No : 169
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
General
BIG DAISHOWA
OCA32-28 (Straight Collet with Oil Hole)
The hydraulic chuck type holder that corresponds to the shank diameter Φ28 is a "hydro chuck".
BBT40-HDC28-75
No : 170
公開日時 : 2024/10/22 00:00
更新日時 : 2025/04/17 07:25
カテゴリー：
Tool selection
In the instructions of the drawing, there are situations where it is difficult to process with standard Tap as follows.
"The screwing length indication is extremely short, and the Tap cannot be inserted to the reference diameter position."
"I'm using it with the tip of the Tap correcte
No : 171
公開日時 : 2024/10/22 00:00
更新日時 : 2025/04/17 07:25