The corners of the end mill are called squares.
Shape of the tip of the end mill (R is the radius)
| Square | ball | corner radius (radius type) |
エンドミル | オーエスジー
34 件中 21-30 件を表示
No : 10348
公開日時 : 2025/03/07 00:00
更新日時 : 2025/04/17 07:24
カテゴリー：
General
A ball is one that has a spherical shape on the entire base. The number after R represents the ball radius. R5 indicates a spherical shape with a radius of 5 mm, and its diameter is 10 mm.
Shape of the tip of the end mill (R is the radius)
| Square | b |
No : 10349
公開日時 : 2025/03/07 00:00
更新日時 : 2025/04/17 07:24
カテゴリー：
General
A cone-shaped peripheral flute end mill is called a tapered end mill.
peripheral flute Shape
Parallel Blade Square End Mill
Tapered Blade Tapered End Mill
No : 10350
公開日時 : 2025/03/07 00:00
更新日時 : 2025/04/17 07:24
カテゴリー：
General
It is the length with peripheral flute from the tip. (It is not the length of the groove.) ）
Name of each part of the end mill
(1) Groove
(2) Shank
No : 10352
公開日時 : 2025/03/07 00:00
更新日時 : 2025/04/17 07:24
カテゴリー：
General
It is an end mill with a wavy cutting edge with a peripheral flute connected to the R (hemisphere) and is designed to reduce cutting force.
The machined surface is rough, and it is mainly used for rough machining. Chips will be fine.
Shape and machined surface of luffing end mill
No : 10355
公開日時 : 2025/03/07 00:00
更新日時 : 2025/04/17 07:24
カテゴリー：
General
What is an end mill that can process right-angle corners? Pinkad Right Angle
If there is an indication for a right-angle corner in the drawing, the end mill side must also be at a right angle. However, in the case of a typical carbide end
No : 7872
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:39
カテゴリー：
Tool selection
What is HY-HSCM-P?
multiple flutes Carbide end mill HY-HSCM-P is capable of high-efficiency machining that of conventional two-blade mills, which is about three times more efficient than feeding.
It is for C chamfering with a taper half-width of 4
No : 13296
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection
Whether or not HY-HSCM-P can be reworked
The regrinding of the HY-HSCM-P is possible.
* The total length changes because the cutting edge is cut.
(FAQID:13297)
No : 13297
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection
What is HY-BCC?
This is a carbide end mill dedicated to 45° back chamfering.
In general, "right-edge, right-handed, right-twisted" front/back tools tend to be "negative cutting" during the back chamfering process, and the finish surface tends to be inferior to that of the f
No : 13298
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection
Whether or not HY-BCC can be re-examined
HY-BCC regrinding is not possible.
(FAQID:13299)
No : 13299
公開日時 : 2024/10/22 00:00
更新日時 : 2024/11/01 02:38
カテゴリー：
Tool selection