エンドミル | オーエスジー

Showing 1-10 of 28 results

answer
What are the recommended end mills for stainless steel?

When used in a machining center, it is recommended to use a helix angle that is stronger than the standard 30° twist.

For carbide end mills, we have the AE-VM series, and for high-speed end mills, we have V-XPM-Hi-Helix specifications.

For general-purpose machines and thin plate processing, it is

No : 351
Published : Modified : 2024/08/28 02:29
Category: Tool selection
answer

What are the characteristics of the selection and processing of end mills in titanium materials? < heat-resistant alloy>

Titanium materials have low thermal conductivity and tend to rise in temperature locally. As for the effect on the tool, it is easy to wear and tear. The cutting force of titanium fluctuates greatly, which is easy to cause tool loss. OSG has an e

No : 381
Published : Modified : 2024/08/28 02:29
Category: Tool selection
answer

What is a keyway end mill?

Since there is a "keyway standard" defined by JIS for keyways, it is recommended that you check the width and depth of the keyway before machining before selecting a tool.

OSG has dedicated end mills for keyway processing in high-speed (EKD), coated high-speed (TIN, V) and carbide (MG).

 

Features of Keyway Tool EKD

<
No : 659
Published : Modified : 2024/08/28 02:29
Category: Tool selection
answer
coarse pitch and Fine Pitch < Roughing End Mills>

The pitch of the nick groove (or R groove) is coarse pitch standard, and the fine pitch is fine.

Wavy cutting edge (luffing): Large incision enables efficient roughing

No : 662
Published : Modified : 2024/08/28 02:29
Category: Tool selection
answer

What is an end mill for V-groove machining?

Currently, we do not have any solid tools that we recommend for V-groove machining.

There are tools with a V-shaped tip (V-cut) shape.

However, this tool is not recommended for V-groove machining, but is used for chamfering with horizontal milling .

References:

No : 670
Published : Modified : 2024/08/28 02:29
Category: Tool selection
answer
How to machine right-angle shapes with an end mill? Sharp Corner Edge Gaze

In order to machine a right-angle shape with an end mill, the tool side that processes it must also have a right-angle shape when rotated. The shape of the tool side is called the sharp corner edge.

The corners of the high-end mill are all sharp corner edge specifications except for t

No : 671
Published : Modified : 2024/08/28 02:29
Category: Tool selection
answer
What is Slotting End Mill? What is STDN?


straight flute Molding end mills are sometimes referred to as slotting. (The twist angle of the groove is 0°)

There are applications that are assumed to be used by the customer with additional work, and applications for molding processing that do not easily cause burrs.

Carbide: MG-STDN<

No : 673
Published : Modified : 2024/08/28 02:29
Category: General
answer
How to use an end mill with 2 blades or 4 blades?

In general, slotting and drilling are difficult to discharge chips, and other processes that require a two-blade end mill to be used.

For machining that is easy to eject chips, such as side cutting, a four-blade ( multiple flutes ) end mill is used to in

No : 675
Published : Modified : 2024/08/28 02:29
Category: General
answer

 Can grooving be done with multiple flutes end mills?

A typical four-blade end mill is not recommended for grooving where chip pockets are narrow and a large amount of chips need to be ejected.

The two-blade end mill has a wide chip pocket and good chip discharge, so it is effec

No : 686
Published : Modified : 2024/08/28 02:29
answer

How much cutting data should be adjusted depending on the flute length and overhang length of the end mill?

The longer the amount of protrusion relative to the diameter of the tool, the more vibration and deflection will occur during machining. By lowering the conditions, it is possible to reduce the force that caus

No : 691
Published : Modified : 2024/08/28 02:29

Searching in progress