タップ | オーエスジー

Tap

Showing 71-80 of 88 results

answer

Please refer to the table below for the pilot hole diameter of the insert screw tap.

Cutting taps for insert screws

・A-SFT HL
・EX-HL-SFT
・EX-HL-POT
・HL-HT

Rolling taps for insert screws

・HL-B-NRT

No : 503
Published : 2019/02/26 18:10 Modified : 2024/08/28 02:29
answer

0.5625-18UNJF is the inch notation of 9/16-18UNJF.

Even with 9/16-18UNF taps, the shape of the internal thread is the same, so if the accuracy is correct, machining is possible.

(The pilot hole diameter of the UNJF must be varied from the size of the UNF.) )

However, you need to pay attention to the thread accuracy.
Screws with a

No : 504
Published : 2019/02/26 18:10 Modified : 2020/10/20 09:41
answer

Once the chamfer is removed, it cannot be cut.

chamfer is the part of the "cutting edge" that is cut by tapping.

If you don't have enough pilot hole depth, consider a short chamfer tap or thread mill.

No : 510
Published : 2019/02/26 18:10 Modified : 2021/06/22 18:16
answer

What is Upper Thirds Tap?

At the request of customers such as "tight when external thread is inserted", "plating on internal thread ", "strain countermeasures by heat treatment after internal thread processing", etc.

Larger screws may be required. In that case, you will use a so-called "

No : 511
Published : 2019/02/26 18:10 Modified : 2024/08/28 02:29
answer

Tool selection based on HRC hardness

When the material to be machined is not listed in the corresponding material column of the catalog, or when the properties have changed due to tempering, etc., the hardness of the workpiece material is one guideline for tool selection.

■ Selection table of drills and taps by material hardness

No : 519
Published : 2019/02/26 18:10 Modified : 2024/08/28 02:29
Category: Tool selection
answer
Normally, there is a protrusion " external center " at the tip of the spiral fluted tap attached to M6 or lower.
No : 522
Published : 2019/02/26 18:10 Modified : 2022/06/09 11:51
Category: Tool selection
answer
Oversize taps for hot-dip galvanizing

Hot-dip galvanizing is also known as dobu plating. Due to the thick plating coating thickness , we do not have a stock product in our company. Depending on the plating thickness, an oversize of about +0.3 mm may be required for the tap.
 
Oversize taps in stock have an ov
No : 524
Published : 2019/02/26 18:10 Modified : 2024/08/28 02:29
Category: Tool selection
answer
Since there are various types of resins, different taps are suitable for different properties.
Thermoplastic resins: Acrylic, vinyl chloride (PVC), etc.

Tools for stainless steel with good sharpness are suitable.


"Thermosetting resins"
Phenol (Bakelite), Epoxy Resin, Yulia, Melamine
No : 535
Published : 2019/02/26 18:10 Modified : 2022/06/17 11:58
Category: Tool selection
answer

Are there any taps that can be processed by 6H?

6H stands for internal thread accuracy.

Is there a tap that can be processed with a internal thread accuracy 6H in the drawing instructions? It means. Separate information such as size and pitch are required.

No : 539
Published : 2019/02/26 18:10 Modified : 2024/08/28 02:29
Category: Tool selection
answer
The spark plug standard is M14S × 1.25. See JISB8031.
Since OH4 falls into the category of OH4 accuracy, A-SFT's M14×1.25 (STD+1) (= OH4) corresponds to it.

M10S×1→OH3
M12S×1.25→OH4
M14S×1.25→OH4

* In 1995, the standards for spark plugs for internal combustion engines were revised.
No : 540
Published : 2019/02/26 18:10 Modified : 2019/12/24 13:19
Category: Tool selection

Searching in progress